I think that says it all, really. And no, you can't brush off that lot by cliaming that the photos were "staged".
Not necessarily. But if that wasn't a perfect analogy, then what about the other one. Ever used an ordinary rubber hot water bottle, Malcolm? Ever emptied it? Just take such a hot water bottle, the morning after the night before, unscrew the cap, and invert. Does the water magically stay there if you don't put any pressure on it?
The only way sealing a container will prevent it from emptying is if the container is
rigid. (Like, for example, a toilet stack if the outlet pipe is blocked.) You can use this property to measure atmospheric pressure, and surely you did this at school. Atmospheric pressure is measured as how high a column of mercury can be supported
under a vacuum. Mercury is used because it is heavy, but water behaves the same way - it's just less practical as you'd need a column many feet high.
But this
DEPENDS ON THE CONTAINER NOT BEING ABLE TO COLLAPSE.
If the container is flexible, like a hot water bottle or a plastic bag, no vacuum can form above the departing liquid, because the air pressure on the outside simply allows the bag to collapse leaving no dead space. This is why flexible bags or thin polythene bottles are used when one wants the contents to flow freely out.
[You can use a rigid bottle, and they used to use rigid bottles back in the dim and distant past - think MASH - but these required some way of letting AIR in, to prevent the vacuum forming and allow the fluid to flow. I've used such bottles for administering chloral hydrate anaesthetic intravenously, and the solution there was to incorporate a flutter valve. The snag with that is that you have to be quick to stop the flow once the bottle is empty, ot the air might go right on flowing into the veins, which is universally agreed to be a Bad Thing. The advantage of using a flexible container which collapses down is that no air is allowed in, and so once the bag is empty the flow will stop of its own accord. It's not GRAVITY you need to let in, Malcolm, it's AIR.
But only if the container is rigid enough to allow a vacuum to form.]
No, Malcolm, most would call it explaining that I'm in a position to know what I'm talking about. Because, unlike you (but in common with a good dozen or so other posters here who are medics, nurses, paramedics, ambulance crew and so on, and who are all telling you the same thing), I have been trained to use the damn things, know how they work, and am experienced in actually using them.
Oh, Malcolm, don't try to move the goalposts. You said "no one remotely connected to medical work would hold up such a bag." We are telling you (and in SpitfireIX's case, eloquently showing you) that yes, they would. That the normal, usual, standard way of administering i/v fluids
requires the bag to be elevated. Whether or not special add-ons are available that eliminate this necessity is not the point. The
routine method requires the bag to be held up.
How long is a piece of string? Specifically, how long do you want it to take? Bags come in 500ml and 1000ml sizes, as standard. They're just bags of salty water, with a port where you can shove the sharp bit at the end of the giving set. It's the giving set that controls the rate. These things incorporate a "drip chamber" which you can see in several of Spitfire's pictures. This is a chamber with a little bit of air through which the fluid has to drip to get down the tube. (Another reason for not laying down the whole thing is it can mess up the operation of the drip chamber, which has to be vertical to work properly.) The purpose of the drip chamber is to allow the flow rate of the fluid to be directly observed. You just count the number of drips falling in, say, 30 seconds or a minute, and that tells you how fast the fluid is flowing into the patient.
The flow rate is regulated by a little thumbwheel or similar device that is fitted to the tube below the drip chamber, and squeezes the tube more or less depending on how you adjust it. More squeeze, more resistance to flow, slower administration. Less squeeze, less resistance, faster flow. Just adjust to requirements, and count the rate the drops are falling to ensure you've got it right.
The size of the drop is determined by the diameter of the tubing entering the drip chamber. Most giving sets are rated at approximately 10 drops/ml. So, if you have a 500ml bag, that's 5000 drops. If you set the drip rate at a drop a second, that would be 5000 seconds, or an hour and 23 minutes. In hospitals, where the drip is often being used just as maintenance for patients on nil by mouth, you'll often see it a lot slower than that, maybe only a drop every three or four seconds. In that case it would take three or four times as long to empty the bag. But on the other hand in an emergency when fast replacement is required, you may set it much higher, even open the thumbwheel entirely, in which case the flow rate will depend on the resistance of the rest of the system - the tubing and the actual i/v catheter being used. MortFurd already explained it.
You can speed it up a bit in this situation by getting the bag as high as possible to increase the "head of water" so that this gravity thing you're having such trouble with will produce a faster flow.
Just LOOK AT SPITFIRE'S PICTURES. You can see the giving sets. You can see the drip chambers. The very name demonstrates that these things need to be approximately vertical to work as designed. The fluid is
dripping DOWN into the patient by gravity.
Malcolm, you just slay me. You had to want a Stundie awful bad to make this much of a fool of yourself.
Rolfe.