Citation needed. What was the make and model of the equipment Grogan used?
Here is what was available to the Canadians.
I am sure other countries had similar technology.
http://jproc.ca/rrp/sradequ.html
"
DF Outfit Nomenclature
DF outfits (aerial, receiver and goniometer) produced for the British Admiralty used the nomenclature
listed below. FH-3, FH-4 and FM-12 sets saw service with the Royal Canadian Navy during WWII.
FIRST LETTER
A = Adcock aerial system
F = Fixed frame coil aerial system
L = loop aerial system
R = Rotating frame coil aerial system
SECOND LETTER
A = Alternative HF/DF or MF/DF
C = Common aerial. For simultaneous reception on HF and MF but alternative DF.
H = HF/DF only
M = MF/DF only
S = Simultaneous HF/DF and MF/DF.
FH-1 HF/DF Outfit
This set was never used by the RCN. It is just
listed here for reference.
FH-2 HF/DF Outfit
There is no evidence to show it was ever used by the RCN so its just
listed here for reference.
FH-3 HF/DF Outfit
Used by the RCN, it relied on operators manually scanning suspected U-boat frequencies. Detection was provided by an audio signal heard in a headphone.Distance was impossible to determine accurately, but operators soon learned to distinguish HF ground waves from sky waves. Since ground waves could only be detected 12 to 14 miles from the transmitter, FH-3 operators knew when an intercepted signal represented a dangerously close U-boat. The FH-3 incorporated the B21B receiver which had a frequency coverage from 1 to 20 Mc. It was connected to a fixed aerial system consisting of two crossed, screened loops (Bellini-Tosi system) for direction finding and a vertical aerial for sense detection. For testing the performance of the apparatus, Frame Coil S25B was used. This is an arrangement in which a signal was injected into the unit and would simulate a bearing at GREEN 45 degrees
While in service, and on a weekly basis, the F/A and P/S loop coils were tested to ensure that their respective resistance did not exceed 0.5 ohms. On a bi-weekly basis, the field coils were tested to ensure that there was not more than 0.1 ohms resistance. Between either loop and ground, the resistance could not be less than 3 megaohms. Search coils could not exceed 0.3 ohms. The FH3 was powered by a 230 volt AC source, which when rectified, produced a B+ of 160 volts to run the receiver. Filament power was 6.3 volts.
Photos of the FH3 receiver and antenna.
FH-4 HF/DF Outfit
This was a 1 to 24 Mc HF/DF receiver which had a cathode ray scope for direct visual bearing indication and was superior to its predecessor due to the ability of being able to distinguish between the sky wave and the ground wave. Its scope was as big as a pie plate, and was surrounded by a compass rose. Accuracy was limited from 2 to 10 degrees and the unit was powered by a 230 VAC 50 Hz mains source. The FH4 was connected to a Bellini-Tosi aerial array consisting of fore/aft (F/A), port/starboard (P/S) loops and a sense aerial. The initial sets were designed with five RF and IF coils that had to be changed for different frequency ranges. In 1945, the set was improved by the addition of a band changing switch.
As one WWII Sparker summed it up: " Changing frequency bands was a bitch with the early model particularly since the set had to be recalibrated every time you did it. Your chances of getting a bearing on a U-boat "B-bar" message of as little as seven letters were abysmal."
FH-4 photos
Select this link to read Authur Bauer's
technical paper on the FH4 DF set.
FM12 MF/DF Receiver See description in HAIDA Radio 4 section.
"